1995 Ford Crown Victoria

Complaint history

When NHTSA received these reports. Changes in reporting alone do not establish a change in failure rates.

Problems owners report

Listed groups have at least 3 complaints. The page includes the 20 largest groups plus any additional flagged groups; some complaints are not assigned to a group.

AI groups complaints by meaning; the groups are approximate. Share ratio compares the problem’s share of this vehicle’s complaints with its share on other vehicles over the last 24 months (shown from 3 recent complaints). A 2× ratio means twice the complaint share, not twice the failure risk. Flags mark unusual shares or recent surges after an AI review of the complaint content. “First signal” does not mean the pattern has persisted continuously.How recall estimates are calculated.

Recalls

• NHTSA recall #08V051000February 4, 2008225,000 vehicles affected

  vehicle speed control: cruise control

  Ford is recalling 225,000 my 1992-2003 econoline, my 1993-1995 taurus sho, my 1992-1998 Crown Victoria, my 1993 bronco, f-series, my 1995-1997 f-series super duty stripped chassis, my 1992-1998 mercury grand marquis, and my 1992-1995 Lincoln town car vehicles. The affected vehicles were previously repaired using a wiring harness that is not compatible with the vehicle circuit polarity.

  As a result, the fuse is located in the output circuit rather than in the intended input power feed circuit, and may not offer the intended protection in the event of an electrical short to ground.

  Remedy

  Dealers will install a new wiring harness, or replace the mating electrical component. The recall began on february 18, 2008. Owners may contact Ford at 1-800-392-3673.

• NHTSA recall #07V336000August 3, 20073,600,000 vehicles affected

  vehicle speed control

  On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.

  This could result in an underhood fire.

  Remedy

  Dealers will install a fused wiring harness. Owners of the passenger cars included in this campaign will be instructed to return their vehicles to their dealers to have the speed control deactivation switch disconnected as an interim repair. As soon as repair parts are available (expected october 2007), owners will be instructed to return to the dealers for installation of a fused wiring harness. The recall began on august 13, 2007, and mailing completed by september 19, 2007. Owners may contact Ford at 1-888-222-2751.

• NHTSA recall #98V322000December 16, 1998175,000 vehicles affected

  suspension: front: control arm: lower ball joint

  Vehicle description: certain 1996-1999 Ford Crown Victoria police, fleet, natural gas, and 1996-1999 Lincoln town car limousine vehicles that were produced with a lower control arm ball joint containing a one piece bearing; and 1990-1996 Ford Crown Victoria police, fleet, and ngv vehicles and 1990-1996 Lincoln town car limousine vehicles that have been serviced with either a ball joint containing the one-piece bearing or a front lower control arm containing a ball joint with a one-piece bearing. The one-piece bearing within the lower control arm ball joint Can weaken slowly during use and eventually crack. This could result in separation of the ball and cap of the joint, allowing the control arm to drop to the ground.

  If this occurs while the vehicle is moving, reduced steering control could occur, increasing the risk of a crash.

  Remedy

  Dealers will replace the lower control arm ball joints (2).

• NHTSA recall #97V024000March 4, 1997125,000 vehicles affected

  latches/locks/linkages: hood: latch

  Vehicle description: police and taxi vehicles. The hood latch striker Can wear or become detached from the hood.

  Either of these conditions Can result in the hood opening without warning while the vehicle is being operated impairing the driver's visibility.

  Remedy

  Dealers will install an improved hood latch striker (vehicles with 1992 model hoods) or revised striker plate attaching fasteners (vehicles with 1993-1997 model hoods).

• NHTSA recall #96V135000July 18, 199672,000 vehicles affected

  steering: linkages

  The pitman arms were not fully lubricated at the assembly plant. The "ball joint" at the outer end of the pitman arm Can become contaminated and corrode.

  Such corrosion Can result in abnormal wear of the joint, resulting in separation of the joint. Loss of steering control Can occur increasing the risk of a vehicle accident.

  Remedy

  Dealers will inspect the vehicles and if the joint is found to have significant wear, the arm will be replaced. Those pitman arms not replaced will have the "ball joint" fully greased.

• NHTSA recall #96V045000March 5, 199649,000 vehicles affected

  seat belts: front: anchorage

  The rivets holding the rear outboard belt d-rings were not heat treated properly causing the heads of the rivets to fracture under load and fail to hold the d-rings to the straps. This does not conform to the requirements of FMVSS no. 210, "seat belt assembly anchorages."

  Consequence of non-compliance: this condition Can reduce the restraining capabilities of the safety belt in the event of an accident.

  Remedy

  Dealers will install a reinforcement plate on the rear outboard seat belt assembly anchorages involved in this campaign.

• NHTSA recall #95V189000October 2, 199545,000 vehicles affected

  electrical system: wiring: fuses and circuit breakers

  These vehicles were built with the non-cycling power window circuit breaker and the cycling headlamp circuit breaker interchanged.

  In the event of a short or overload in the headlampcircuit, both headlamps Can go out without warning, rather than flashing as intended with the cycling circuit breaker. This could lead to reduced night time driver visibility, increasing the potential for a vehicle accident.

  Remedy

  Dealers will inspect these vehicles, remove the circuit breaker and reinstall the breaker in the correct locations.

• NHTSA recall #95V063000March 27, 1995100,000 vehicles affected

  fuel system, gasoline: storage: tank assembly: filler pipe and cap

  The seal material between the fuel filler pipe and fuel tank may not have been fully cured during the molding process which could allow for fuel leakage.

  Fuel leakage could result in a vehicle fire if an ignition source were present.

  Remedy

  Dealers will replace the fuel filler pipe-to-fuel tank seal with a new seal of different material.

Other model years

• 1986 27
• 1987 41
• 1988 42
• 1989 72
• 1990 43
• 1991 55
• 1992 310
• 1993 182
• 1994 192
• 1995
• 1996 276
• 1997 288
• 1998 119
• 1999 134
• 2000 85
• 2001 53
• 2002 58
• 2003 249
• 2004 138
• 2005 193
• 2006 53
• 2007 50
• 2008 50
• 2009 44